Motor Gear

The Hana Gloves mixes classic Bison with a high end Japanese floral fabric patterned top. These gloves are made in the USA.

SIZE CHART

MEASURE AROUND YOUR PALM

XS: <7”

SMALL: 7-7.5”

MEDIUM: 7.5-8.5”

X-KD's are 20 percent larger than The Original KD's

- Lightweight
- 100% UV protection
- Long slim arms for better peripheral vision
- Fits comfortably under a helmet
- Acetate frame with wire reinforced temples
- Ultra-tough Polycarbonate lenses

- Meets ANSI Z80.3 standards
- Total Frame Height 1-5/8" (4.19cm) Total Frame Width 5-3/4" (14.60cm)

• 100% Leather
• Prism Supply Branding
• Short to Medium length cuff
• Fleece lined
• Cinch rope

It's best to look slick while you're taking 1st place...or just when you're out ripping with the crew!

• 100% polyester mesh
• Classic moto jersey material

Renegade is identical to our Thruster model—tall flange, thick end cap—but features the football-shaped file pattern grip section as our Recoil grip. A great grip for big hands.

Technical Details

• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick one-piece molded end design for durability
• Tall inner flange protects your hands from discomfort against throttle and hand controls
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls
• 1" White

Football-shaped cross section is fat in the middle and smaller on both ends to follow the contours of your open fist. Super durable and great looking, Recoil is our classic chopper grip

Technical Details

• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick, tapered one-piece molded end design for durability
• No inside flange give Recoil a classic chopper vibe
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle
• 7/8" Grey

Football-shaped cross section is fat in the middle and smaller on both ends to follow the contours of your open fist. Super durable and great looking, Recoil is our classic chopper grip

Technical Details

• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Thick, tapered one-piece molded end design for durability
• No inside flange give Recoil a classic chopper vibe
• Safety wire grooves on grip ends for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle
• 1" Oxblood

Our Kung Fu grip's squishy surface design is cozy the second you grab it. New UV-resistant TPV synthetic rubber is soft, yet durable for miles of comfort.

Technical Details

• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Medium inside flange cushions rider's hands from rubbing the throttle and controls
• Thick outer flange for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Our Kung Fu grip's squishy surface design is cozy the second you grab it. New UV-resistant TPV synthetic rubber is soft, yet durable for miles of comfort.

Technical Details

• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Medium inside flange cushions rider's hands from rubbing the throttle and controls
• Thick outer flange for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

CE Utility Mirrors boast clockworks precision and timeless style to stand out or blend in on any stock or custom motorcycle you can imagine.

Technical Details

• Die cast aluminum mirror head
• Tempered mirror glass
• Can be ran in the up or down position
• Hinged p-clamp handlebar mount
• Mirror head angle adjusts via ball and socket assembly
• Chrome finish

One of the first investment-cast parts remains a popular bolt-on for DIY customizers and pro builders alike. Stainless steel for durability and pure vintage style. One-inch bar clamps and 1/2-13 t.p.i. mounting holes make our Slimline riser a great choice for a wide range of custom motorcycles.

Technical Details

• Investment-cast stainless-steel construction
• 1.75-inch rise from mounting base to center line of handlebar clamp
• Polished raw or black electroplated finishes available
• Accepts stock H-D or aftermarket 1/2-13 t.p.i. mounting hardware
• Bar clamps feature 5/16-18 t.p.i. stainless-steel Allen cap screws

The Mustache handlebar has less aggressive styling than the Biltwell Zed bar that inspired it, but it's similar in every other way. Narrow, for splitting lanes. Black electroplate, for surface protection and beauty.

Technical Details

• Seamless 0.120" (3mm) wall 4130 chromoly construction
• Tight 90-degree CNC mandrel bends
• CNC mitered tube ends for clean joints and precise alignment
• TIG welded construction for beauty and strength
• Black electroplate
• Non-Dimpled
  

Don't strap down your gear with generic tie-downs or an old bungie cord. EXFIL straps come in two sizes to secure a range of loads from light-as-a-feather to packed-to-the-moon. Each set includes two straps—buy two sets and be prepared for anything.

Technical Details

• Woven high-tensile polyester nylon straps with woven reflective thread detailing
• Contrasting bar-tacked thread construction in critical high-stress, load-bearing areas
• Reinforced nylon one-piece buckles with serrated teeth clamp straps hard, won't loosen under stress
• Knotted, orange elastic shock cord loop secures long end of strap after installation

Big and strong enough to hold a full set of motorcycle service essentials, yet still compact enough to fit inside most bags. EXFIL-0 is the perfect complement to every self-reliant bikerider's kit.

Technical Details

• Highly abrasion-resistant 600 denier polyester nylon outer shell
• Heavy-duty hi-vis orange nylon interior lining
• 7 elastic socket holders
• 5 pockets for wrenches
• Adjustable G-hook nylon strap closure
• Internal zipper compartment for small items
• Closed dimensions 9.25” x 7.0"; 18.5” long when opened flat
• Tools shown for illustration only—not included

Moto 2.0 features a wide peripheral arc for enhanced side vision. The frame's interior volume is large enough to fit over many styles of prescription eyewear.

Technical Details

• Injection-molded flexible polyurethane frame
• Flexible, impact-resistant polycarbonate lens to ward off flying debris
• Woven elastic strap with double D-rings for fast, easy tension adjustment
• Silicone traction strips on back of strap reduce slipping on the helmet shell
• 2-phase foam around eye port wicks sweat, dries fast, filters dust
• Anti-fog treatment dissipates moisture build-up on inside surface of lens
• Meets European CE EN1938:2010 standard for recreational motorcycle operation

Aesthetically vintage and optically precise, our highly scratch- and impact-resistant polycarbonate shields fit helmets with three snaps across the brow, and come in a Skittles sack of molded colors and reflective coatings.   

Technical Details

• Injection-molded scratch- and impact-resistant polycarbonate thermoplastic construction
• Plated stainless-steel snaps fasten securely to snaps on helmet brow for easy installation
• Colored shields feature in-molded tint technology
• Mirrored shields feature reflective technology in a variety of surface finishes to reduce glare
• Every shield color and style provides 91% UV/A and 99% AV/B light resistance based on AATCC-138 test standard
• Anti-fog treatment on shield interior fights moisture build-up from breathing and humidity 

Gringo takes its '60s motorsport aesthetic and elevates it to modern ECE R22.05 motorcycle standards—the European test protocol recognized by leading helmet makers and independent safety labs as the toughest in the world.

Technical Details

• Injection-molded ABS outer shell is rugged yet lightweight—the best combination of features for a motorcycle helmet
• Three-piece Expanded Polystyrene (EPS) safety liner dissipates impact loads and fortifies helmet structure for a secure fit without compromising comfort
• Molded urethane chin bar pad dissipates energy during frontal impacts
• Removable/replaceable comfort liner and cheek pads feature brushed fleece Lycra touch points to absorb and evaporate perspiration
• Chin strap features brushed fleece Lycra touch points for comfort and an adjustable strap end retainer
• Molded recesses inside EPS designed to accept various aftermarket audio and communication components

Size chart

Gringo ECE Helmet - Flat Black